Archive | December, 2014

Filament review: ColorFabb PLA-PHA variables

23 Dec

Filament review: ColorFabb PLA-PHA variables

This is the filament I have the most experience with, on both good and bad. I purchased my first rolls 1.5 years ago. I had worked really hard for a long time and thought that I would reward myself with some prime quality filament so I stocked up on 10 rolls of all the colors I wanted!

Up until buying from ColorFabb, I had only used filament from high quality vendors like Faberdashery, Diamond Age and Ultimachine. Given all the positive comments I'd seen from others I expected the same (or maybe even better?) from this Dutch vendor. I was wrong. Months of clogged extruders ensued.

The cost of troubleshooting

I purchased spare parts for several hundred Euros from Ultimaker, just so I could exclude that as being the problem. I practically rebuilt the entire extrusion system without being able to solve the clogs. I even went as far to buy a proper Fluke HWAC multimeter so that I could measure temperatures properly. I also incorrectly blamed Ultimaker & Cura for some of the issues hmmm

Tons of tests...

I eventually came down to the conclusion that the clogs came from inconsistent diameters (sometimes above 3mm, far from 2.85mm) and very varying quality of the plastic. For most plugs I'd find some black thing at the nozzle tip while cleaning it out. I should point out that cleaning out an ultimaker isn't very simple as you'll often have to disassemble half the print head. Not a fun task to do several times a day, especially since I also printed 800+ meters of Faberdashery plastic on the same printer without a single filament error...

Replacement rolls

I wrote several polite emails with the support crew at ColorFabb and I have to say their support is really stellar. Nothing to complain about there. They told me that both the formulation & diameter had been off on several of the early rolls, and offered to replace all my rolls with new filament at no cost. That's pretty good service?

Problem was - when I got the rolls, some of them were better but by no means all. Argh... I've paid almost 450 EUR for those rolls, I have to make them work! After a lot of testing & rebuilds of extrusion system on my Ultimaker, I came to the conclusion that the only way I could print with them was going far above the recommended 210C. Even then it would clog now and then if I tried to go too fast. Others at my hackerspace had similar experiences, but a friend using 1.75mm Colorfabb filament never has issues? My Ultimaker Original is equipped with a 100% original extrusion system and the only speciality is the added dual extruder & heated bed. None of these should have any effect on the printing.

New printer, new problems

I solved most my ColorFabb problems by printing really hot and cooling the Ultimaker hotend down with an extra fan as I printed. If I tried to go anywhere near their official recommendation, the printer would clog right away. This worked so well that when I built my new printer, I was completely flabbergasted when I got similar problems here. The new printer had an E3D hotend that I had heard tons of positive feedback on. As soon as I added ColorFabb's PLA/PHA, the printer choked unless I printed at 20-30C above the recommendation.

After a month of trying to solve the problem without using extra heat, I gave up. I then realised that my roll of Ultra Marine Blue didn't have a consistent color? The color varied quite a bit along the roll. I contacted ColorFabb and yet again they replaced the roll. Excellent service, and this time half the roll have printed nicely. Strange?

Tangles! I never had that with any other vendor of plastic on spools hmmm

The PLA / PHA combo has major differences from other vendors. One is the addition of PHA, another bioplastic. It is apparently this that gives this PLA it's shine and makes it less brittle than other PLA. I'm by no means an expert on bioplastics, but there is something that makes this PLA/PHA mix more prone to stick to the inside walls of the extruder. Most often, you'll pull this buildup out with the filament after a blockage, but some will remain and must be removed with the "Atomic pull" method.

I've learned that most industry players use PLA from NatureWorks. ColorFabb buys their PLA from FKuR Kunststoff in Germany. I dunno what to say other than that it has some other (and less desirable) properties than the NatureWorks PLA. ColorFabb did however tell me that they only use NatureWorks PLA in their transparent PLA filaments and sure enough - it performs a lot better.

Colorfabb's response

ColorFabb says that the printer settings may vary (even among the same model) and that their recommendations can't work for everyone. I must say that I find frustrating to hear that from a vendor when all my 3 printers (PrintbotJr, Ultimaker Original, BAMM) as well as friends printers need to go to the same high temperatures to extrude it well. What makes this even more frustrating is that companies like MadeSolid publish guidelines for lots of printers and these worked for me right away?

I am now printing successfully with PETG from MadeSolid, PLA from Faberdashery, some really old ABS from Makerbot (back when they made 3mm filament), ABS from Protoparadigm, Proto-pasta's carbon fibre infused PLA, 2 year old PLA from Diamond Age, NinjaFlex, PLA/ABS/flexible rubber from PlastInk, PLA from Ultimaker and even Taulman 618/645 Nylon. Not a single blockage with any of these, but as soon as I insert the PLA/PHA mix from Colorfabb, my extruder will clog up. How fast this happens will vary, but I can't trust it for longer prints.

I just had to throw away two entire rolls of white PLA/PHA since the quality was so inconsistent that the layer height varied so much it was clearly visible (see below). Printing the same object with the same settings using Silver colored Ultimaker PLA gives me excellent looking results:

They're so different that you'd think it was printed on two different printers? This really is a shame as my two black rolls of PLA/PHA (made the same month!) will produce great looking results, even at fairly low temperatures???

I have completely given up on ColorFabb and it's a shame as they make so many cool things such as WoodFill, CopperFill & BronceFill. I just can't afford to spend more time on it as I've easily spent more than 100 hours cleaning out nozzles, solving clogs and failed prints. That's bad for business and not what I'd call "production quality". It's simply too inconsistent. I have a "trick" of working with it that "sort of" works and that's doing 5-6 atomic pull's with Taulman 645 Nylon before anything more than tiny prints. I'm also printing at speeds far higher than I like (due to the mass of the 30x30cm heated bed). This causes bandings in the prints, but then at least I can use the filament rather than just throw it away. It'll still get me plenty of jammed nozzles though.

Since MadeSolid now sells 15 different colors, so I'll get my PETG from them instead. As for PLA - rumours say that Faberdashery will soon begin shipping their 28 different plastics on spools. I guess I might buy my xmas filament from them instead.

BAMM settings for ColorFabb PLA/PHA

The BAM Makeblock printer has a BulldogXL extruder with a Hexagon nozzle. I use the following settings with PLA/PHA from ColorFabb:

  • Temperature: 220-240C
  • Speed: 70mm/sec (faster = less jams / clogs)
  • Retraction: 1.5mm @ 20mm/sec (less retraction = less deposits)
  • Extruder tension: screws 0.0mm out (solid pressure)
  • Heated bed: 50C
  • Fan: full (to compensate for excessive temp required to prevent plugs)